跳至主要内容

Three small details to analyze the jam of the plastic shredder

 In recent years, plastic shredders have become more and more widely used in the market, but plastic shredders will inevitably encounter some problems in the process of use, such as jams, which cause jams. It is not a unilateral feeding of more materials. It is jammed, but it is necessary to solve the jamming problem of the plastic shredder from the source.


1. The requirements for output do not match the power of the equipment. This is also required for the material of shredded plastic. For shredding is easier, the feeding speed can be correspondingly accelerated, but for those difficult to tear, the feeding speed should also be reduced.Feeding reasonably according to the material of the plastic can avoid jamming.


2. The discharging pipeline is blocked, causing the conveyor to run idly, and the conveying can not come out and jamming. During the operation of the plastic shredder, you must always pay attention to the abnormal phenomenon of the equipment. Listen and watch more to avoid jams.


3. The water content of waste plastics is too high and the viscosity is high, causing adhesion and jamming. Analyze the reasons for the high moisture content of waste plastics. The moisture content of the material itself is high, and this probability is not very high. In addition, the materials are exposed to rain or soaked in water. In such a case, the materials should be dried before being shredded so as to avoid jamming.


It is more and more widely used in the market. The reason is that the plastic shredder equipment has a good shredding ability for various materials. The plastic shredder reduces the speed of the rotor through a reducer and increases the torque of the rotor. Through the squeezing and shearing of the cutter, the shredding ability is achieved. Because of the low speed, it will not generate a lot of heat, and will not melt the plastic in the shredding chamber. Large pieces of material can be shredded in whole pieces. Obviously, high efficiency and low noise are the main plastic shredder equipment now and in the future.


As a professional shredder manufacturer and supplier, Shuguang Heavy Machinery's double shaft shredder can shred common domestic waste, and has a special production line to treat waste tires into small particles, which are used as raw materials in many fields.Welcome to contact us for more details.

 

Factory Address: Longjiang West Road, Shangjie District, Zhengzhou City

Contact number: +86-371-67666660 676667

Mobile phone: 0086 13523465141

After-sales Service Department: 0371-67666667

评论

发表评论

此博客中的热门博文

What to do if the metal shredder discharges unevenly

 In the course of use, the metal shredder has uneven discharge. Through analysis, Shuguang heavy machinery summarized the following reasons. First of all, because the voltage is unstable, it will affect the stability of the motor, resulting in uneven speed, fast and slow and other problems, which will worsen the uneven discharge. When the feed is uneven, it is easy to block and cause the cavity to become clogged. Fully process unfinished materials. In severe cases, many blockages may cause downtime or increase in motor temperature.  Secondly, the motor is unstable. When the voltage is stable, following the change of the force endured by the transmission, the fixed point of the motor will be displaced and the base screw will be loosened.  Therefore, it is necessary to check whether this part is complete. First, the current professional standards for shredders are not standard, and the supporting shredder blade standards are also complicated. The shredder produced by the s...
发表评论
阅读全文

How to Avoid Faults in Aluminum shredder

The main purpose of scrap  aluminum shredder  equipment is to tear all kinds of unqualified scrap iron into smaller pieces for recycling. Reduce the volume of unprocessed raw materials for mixing with other materials. How to avoid equipment failure in daily production of scrap aluminum shredder equipment?   1. Check and clean in time. After work every day, the machine should be cleaned in time. Check screw loosening and abrasion of easily worn parts such as claws, sieves, etc. http://www.sg-shredder.com/News/Industry_News/755.html
发表评论
阅读全文

How to deal with the heating problem of shredder motor

When we use the motor for a long time, there will be the problem of motor heating. The motor will lack of oil after a long time, which will affect the production efficiency of the whole shredder equipment . If the motor is hot or burnt, there is no way to tear it. How to avoid the phenomenon of motor heating of the shredder? 1. The adjustment of the tension of the V-belt of the shredder equipment, when the V-belt is too tight, the motor bearing heats up, when the V-belt is too loose, the rotation speed decreases, and the V-belt is easy to slide, which all affect the service life. When adjusting the tension of the V-belt, the bolt fixing the motor base can be loosened, and the position of the motor on the slide way can be changed with the adjusting bolt, so that the V-belt can reach the required tightness, and then the fixed bolt can be tightened; 2.After the shredder motor works for a certain period of time, it is necessary to add oil or open the cleaning bearing and refill the file ba...
发表评论
阅读全文